Your basket is currently empty!
Heat Press Settings
Here are the Heat Press Settings
Read more
Explanation of the terms
Let’s start with pressure. This is expressed in bar(s) and divided into three criteria:
Low pressure: A pressure distribution of 2-3 bar.
Medium pressure: A pressure distribution of 4-5 bar.
High pressure: A high pressure of 6-8 bar.
With pneumatic transfer presses (using air pressure), you can set the pressure to a specific level of bar.
Prepress
Pre-pressing without transferring directly onto the fabric. This has several advantages:
It ensures good moisture in the fabric, which promotes the transfer process. An exception is polyester: It’s better not to pre-press polyester to reduce the risk of bleeding, and polyester doesn’t wrinkle and can’t absorb as much moisture as cotton, so pre-pressing isn’t necessary at all.
It ensures a smooth surface, allowing you to position the transfer as desired.
Temperature / Fahrenheit
Temperature / Fahrenheit
Temperature is especially important for processing any type of film. If you’re unsure or want to know if your heat press is at the correct temperature, you can order temperature strips.
Time
Time
Try to keep the time as accurately as possible. Our manuals have been carefully and extensively tested and are recommended for best results.
Pressing
Repressing
Repressing is pressing the image again after printing with a sheet of release paper. If additional pressing is necessary, this ensures better adhesion to the product. However, it’s also possible that the adhesion decreases after pressing, or the image becomes less attractive. Therefore, we always indicate in the manual and in the overview above whether repressing is necessary or not, for the best results.
TheMagicTouch Heat Press Settings
| Transfer Paper | Pressure | Pre-Press | Temperature | Time | Peel | Post-Press | Accessories |
| TTC 3.1 | High | – | $180-195^\circ\text{C}$ | $10-15$ seconds | Hot Peel | $3-5$ seconds | – |
| TTC 3.1 Plus | High | – | $180-195^\circ\text{C}$ | $10-15$ seconds | Hot Peel | $3-5$ seconds | – |
| OBM 5.4 | High | $5$ seconds | $120^\circ\text{C}$ | $15$ seconds | Warm Peel | – | TheMagicTouch T.Seal |
| WOW 7.8 (Step 1) | High | $5$ seconds | $130-145^\circ\text{C}$ | $15-60$ seconds | Hot Peel | – | TheMagicTouch T.Pad |
| WOW 7.8 (Step 2) | High | $5$ seconds | $140^\circ\text{C}$ | $5$ seconds | Cold Peel | $15-20$ seconds | TheMagicTouch T.Seal |
| T.ONE | High | $5-10$ seconds | – | $5-15$ seconds | Warm Peel | $15-20$ seconds | TheMagicTouch T.Seal |
| CPM 6.2 | Product dependent | – | $140-150^\circ\text{C}$ | – | – | – | – |
| RST 9.1 | High | – | $160^\circ\text{C}$ | $60$ seconds | Wet Peel | – | TheMagicTouch Application Sponge |
| ORD 8.1 | High | – | $130^\circ\text{C}$ | $15$ seconds | Cold Peel | – | TheMagicTouch Application Sponge |
Transfer press settings for MagiCut
| Article | Pressure | Pre-Press | Temperature | Time (seconds) | Peel | Post-Press |
| 123Flex (Low Temp) | Medium | Not needed | $130^\circ\text{C}$ | $10-15$ | Warm Peel | Not needed |
| 123Flex (High Temp) | Medium | Not needed | $155^\circ\text{C}$ | $3-5$ | Warm Peel | Not needed |
| 123Flex Block Out | Medium | Not needed | $130^\circ\text{C}$ | $10-15$ | Warm Peel | Not needed |
| 123Premium (Low Temp) | Medium | Not needed | $130^\circ\text{C}$ | $10-15$ | Cold Peel | Not needed |
| 123Premium (High Temp) | Medium | Not needed | $155^\circ\text{C}$ | $3-5$ | Cold Peel | Not needed |
| 123Premium Block Out | Medium | Not needed | $130^\circ\text{C}$ | $10-15$ | Cold Peel | Not needed |
| 123Premium Ultra (Low Temp) | Medium | Not needed | $130^\circ\text{C}$ | $10-15$ | Warm Peel | Not needed |
| 123Premium Ultra (High Temp) | Medium | Not needed | $155^\circ\text{C}$ | $3-5$ | Warm Peel | Not needed |
| Dimension | Medium | Not needed | $150^\circ\text{C}$ | $15$ | Cold Peel | Not needed |
| Flock (Low Temp) | Medium | Not needed | $130^\circ\text{C}$ | $15-20$ | Cold Peel | Not needed |
| Flock (High Temp) | Medium | Not needed | $150^\circ\text{C}$ | $10$ | Cold Peel | Not needed |
| Glitter | Medium | $5$ seconds | $155^\circ\text{C}$ | $15$ | Cold Peel | Not needed |
| Glow (in the dark) | Medium | $5$ seconds | $160^\circ\text{C}$ | $15$ | Cold Peel | Not needed |
| Holographic | Medium | $5$ seconds | $160^\circ\text{C}$ | $15$ | Cold Peel | Not needed |
| Hotmelt (Low Temp) | Medium | Not needed | $130^\circ\text{C}$ | $10-15$ | Warm Peel | Not needed |
| Hotmelt (High Temp) | Medium | Not needed | $155^\circ\text{C}$ | $3-5$ | Warm Peel | Not needed |
| Metallic | Medium | $5$ seconds | $155^\circ\text{C}$ | $20$ | Warm Peel | $10$ seconds |
| Photochromic | Medium | $5$ seconds | $150^\circ\text{C}$ | $10$ | Warm Peel | Not needed |
| Puff | Low | $3$ seconds | $140^\circ\text{C}$ | $10$ | Warm Peel | Not needed |
| Puff (Metallic colors) | Low | $3$ seconds | $140^\circ\text{C}$ | $10$ | Warm Peel | $15$ seconds |
| Rainbow Spectrum | Medium | $5$ seconds | $150^\circ\text{C}$ | $10$ | Cold Peel | Not needed |
| Reflex | Medium | $3$ seconds | $150^\circ\text{C}$ | $10$ | Warm Peel | Not needed |
| Soft Metallic (Low Temp) | Medium | Not needed | $130^\circ\text{C}$ | $10-15$ | Warm Peel | $10$ seconds |
| Soft Metallic (High Temp) | Medium | Not needed | $155^\circ\text{C}$ | $3-5$ | Warm Peel | $10$ seconds |
| Stretch (Low Temp) | Medium | Not needed | $130^\circ\text{C}$ | $10-15$ | Warm Peel | Not needed |
| Stretch (High Temp) | Medium | Not needed | $155^\circ\text{C}$ | $3-5$ | Warm Peel | Not needed |
| Twinkle | Medium | $3$ seconds | $150^\circ\text{C}$ | $15$ | Cold Peel | Not needed |
| Eco Gloss Finish | Medium | Not needed | $130^\circ\text{C}$ | $15$ | Cold Peel | Not needed |
| Eco | Medium | Not needed | $150^\circ\text{C}$ | $5$ | Warm Peel | $10$ seconds with TheMagicTouch T.Seal |
| Silicone | Medium | Not needed | $150^\circ\text{C}$ | $20$ | Cold Peel | Not needed |
Poli-Flex Heat Transfer Vinyl (HTV) Press Settings
| Article | Pressure | Pre-Press | Temperature | Time (seconds) | Peel | Post-Press |
| Poli-Flex Block Out | Medium | Not needed | 130°C | 5 | Warm Peel | Not needed |
| Poli-Flex Chalkboard | Medium | Not needed | 130°C | 5 | Warm Peel | Not needed |
| Poli-Flex Glitter | Medium | 5 seconds | 160°C | 15 | Warm Peel | Not needed |
| Poli-Flex Glossy | Medium | 5 seconds | 160°C | 15 | Warm Peel | Not needed |
| Poli-Flex Image | Medium | Not needed | 160°C | 15 | Warm Peel | Not needed |
| Poli-Flex Nylon | Medium | Not needed | 150°C | 5 | Warm Peel | Not needed |
| Poli-Flex Premium | Medium | Not needed | 160°C | 15 | Warm Peel | Not needed |
| Poli-Flex Reflex | Medium | Not needed | 145°C | 8 | Cold Peel | Not needed |
| Poli-Flex Turbo Reflex Silver 4783 (on Polyester) | Medium | Not needed | 130°C | 5 | Warm Peel | Not needed |
| Poli-Flex Turbo Reflex 4783 (on Cotton) | Medium | 5 seconds | 160°C | 5 | Warm Peel | Not needed |
| Poli-Flex Premium Reflex 4782 | Medium | Not needed | 160°C | 15 | Warm Peel | Not needed |
| Poli-Flex Reflex 4781 (EN-Norm) | Medium | 5 seconds | 160°C | 15 | Warm Peel | Not needed |
| Poli-Flex Nylon 4882 | Low | 4 seconds | 150°C | 5 | Warm Peel | 10 seconds |
| Poli-Flex Stretch | Medium | Not needed | 160°C | 15 | Warm Peel | Not needed |
| Poli-Flex Turbo (on Cotton) | Medium | 5 seconds | 130°C | 5 | Warm Peel | Not needed |
| Poli-Flex (on Nylon) | Low | 5 seconds | 150°C | 5 | Warm Peel | 10 seconds |
Transferpers instellingen voor Sef textile
| Article | Pressure | Pre-Press | Temperature | Time (seconds) | Peel | Post-Press |
| Premium Flock – Velvet Eco | Medium | 5 seconds | 165°C | 17 | Cold Peel | Not needed |
| Fantasy & Crazy Flex | Medium | 5 seconds | 140°C | 10 | Cold Peel | 10 seconds |
Frequently Asked Questions
Want to ensure a perfect transfer? All our films have been extensively tested. Start every production run with a test print and discover the difference for yourself. Have any questions? Our support team is happy to help.
In the table below, you’ll find the recommended settings for each transfer paper, flex film, and more. In addition to temperature, time, and pressure, you’ll also find whether the film is suitable for multi-color designs, the maximum washability, and the thickness.
4.6
